Home
Search results “How to revive a lithium battery”
DIY: How to revive a dead 18650 (or any) Li-ion battery cell
 
04:37
Today I will show you how to revive a dead 18650 Li-ion cell that's being refused by the chargers. This method will work with any Li-ion battery, not just the 18650 cells. Here's my follow-up video:https://youtu.be/vFmbG8GpS4A if you wonder how much current (Amps) goes through the wire. Note: this is not a permanent way to charge an 18650 cell. The point of this method is just to bring up the voltage of the dead cell to a point that is enough for a real 18650 charger to accept it and charge it properly. When a Li-ion battery does not have high enough voltage, the charger would not charge it. I think the reason is safety because if the voltage is too low, it might take a risk of charging a NiMH or NiCad cell which are only 1.2 volts each. And if you put a NiMH or NiCad cell (at 1.2 Volts) in a Li-ion charger that charges up to 4.2 volts, all hell will break loose. Also: don't overdischarge a Li-ion cells down to below 3V especially below the threshold recognized by the charger. Otherwise, it will not live long. The "Goldilocks" zone for a long and healthy Li-ion cell life is between 30% and 90% charge. Too much charge or discharge would be bad for the cell.
Views: 393568 vuaeco
DIY: How to Revive a dead Li-ion power tool battery
 
08:15
Fix your dead battery by using a DC power source to raise its voltage. Note: do NOT use a DC power source with more voltage than the maximum rated voltage of the dead battery. If you have a regular 18V or 20V battery pack, that's 21V max (4.2V x5). Do not use a DC power source more than 21V to revive the dead 21V battery. About the wires with alligator clips: make sure you use heavy gauge wires size AWG 14 or bigger. The alligator clips with attached wires from Harbor Freight are not going to make it as the wires are too thin and they will heat up and just melt or burn the insulation right away. And make sure to monitor closely what you're doing cause it might heat up things quickly. As soon as you get the desired voltage (about 16V or more for this kind of batteries), just remove the alligator clips and put the battery in the charger. In other words, just do the parallel charging as minimal as possible and just enough for your charger to recognize the dead battery.
Views: 366990 vuaeco
"Fixing" Li-ion Batteries that wont take a charge
 
06:29
Does your li-ion battery fail to charge in the charger? This DIY method shows how to wake dormant Li-ion cells above thier low threshold voltage allowing them to be charged normally. WARNING! Try at your own risk, these batteries can explode!
Views: 227958 Donnie Cox
How to revive a Ryobi 18 volt lithium battery. Quick and easy
 
04:21
Don't buy new battery just Restore revive 18-volt lithium battery P102 by drilling two holes on a battery one on each side of the battery pack and boosting the energy back to the power source with some kind of power supply to reboost using two pieces of wire about a foot length placing the wires into positive to positive and negative to negative . If this Method doesn't work for you I have a completely different solution for that just let me know with a message and I'll make a new video for you. Guaranteed the new Method . My other link for Ryobi lithium battery p108 https://youtu.be/OAt5TTq_4fw
Views: 155166 tomstuff460
Revive & Maintain your Lithium-Ion Motorcycle Battery - Snitchy1989
 
15:22
A tip on how to revive and maintain a motorcycle lithium ion battery. If it feels sluggish to crank over your engine, here is a simply method to revive it perfectly, and also the reason why! Donations welcome: Paypal: Snitchy1989@outlook.com (All donations will go toward channel/equipment improvements) - You will also get a massive thankyou, aswell as a shoutout in one of my videos -
Views: 519 Snitchy1989
How to Revive a "Dead" Ryobi 18 volt Lithium Battery - 582
 
12:37
I am really happy with my Ryobi tools. My friend that got me hooked on this nice semi-prof brand of cordless tools, had a battery that would no longer charge. And I got it to try to do this revival video :-) Link to Angle Grinder this on Amazon : - http://amzn.to/1QfwKQf Link to Ryobi 18-Volt Li-ion 4Ah Battery - http://amzn.to/1QfxcOp _________________________________________________________________ http://www.patreon.com/myplayhouse Even just 1$ a month, comes out to the same as Binge-watching all of my 500+ Videos every month. My PlayHouse is a channel where i will show, what i am working on. I have this house, it is 168 Square Meters / 1808.3ft² and it is full, of half-finished projects. I love working with heating, insulation, Servers, computers, Datacenter, green power, alternative energy, solar, wind and more. It all costs, but I'm trying to get the most out of my money, and my time.
Views: 22416 My PlayHouse
2 way's how to fix 3.6 /3.7 volt  death lithium smartphone battery not charging with phone adapter
 
17:07
Also : How to use your Smartphone without a battery . Kickstart your sleeping not charging smartphone battery ? Name of device i,m using is the HQ Digichart 120 battery charger In this video you will learn how to jump start a sleeping death not charging battery back to life so it can continue charging in the phone... This is only for Lithium batteries of 3.6 / 3.7 volts and no other. Don't pity more power because these batteries can explode, so be careful. Video Channel48 By Puck Darlington (c) 2016
Views: 49288 channel48
Repairing a Li-Ion battery (18650) DON'T TRY IT!
 
01:55
Dangerous stuff !! DON'T TRY THIS AT HOME More about this here: http://bit.ly/VX8o4Y
Views: 306025 furulevi
How to revive Ryobi lithium battery P108 . Quick and easy
 
04:46
My p108 lithium Ryobi battery has gone dead and I'm going to try to revive this battery with my old method so you guys can can do the same. Remember just drill the plastic only NOT the terminal or the batteries in the inside. is going to work for you it worked for me if you like this video please click like. Thanks for watching My Link for my Ryobi lithium batteries P102 https://youtu.be/acxUsuo8dVg
Views: 42025 tomstuff460
Lithium Ion Battery - Explained
 
05:12
What is lithium ion? How do lithium ion batteries work? Lithium batteries work just like lead acid batteries, except they allow for the flow of lithium ions between the anode and cathode of the battery, as the electrons flow through the conductive connection. Lithium ion batteries are the popular choice for modern electric vehicles, due to their many advantages over lead acid batteries. -- Related Videos -- Batteries: http://youtu.be/vSzmbFf4Pyo Please feel free to rate, comment, and subscribe! And don't forget to check out my Facebook page: http://www.facebook.com/engineeringexplained Also check out my official website: Make suggestions, participate in forums, learn through logically ordered lessons, read FAQs, and plan your future! http://www.howdoesacarwork.com Now on Twitter: http://www.twitter.com/jasonfenske13 NEW VIDEO EVERY WEDNESDAY!
Views: 251683 Engineering Explained
Reviving a Lithium Ion Battery Pack from Ebike. (pt. 1)
 
00:56
7s 26650 pack was at 4v after recovery from an ebike. should be 29.4v fully charged. Bumping it up with a 12v power supply at 1.5a (bulk charging) Next step is to bulk charge up with a 24v source, then the BMS should accept charge through the original charger and after a few days, should actually function (a little).
Views: 171 Lotrwiz
How to Revive a Dead 18650 Li-ion Battery Cell After Overheat
 
01:57
In this video I show you how to recovery 18650 batteries, after protection has tripped after overheat.
Views: 123 Duct tape
revive a dead 18650  or any  Li ion battery cell only 1 minute
 
02:07
today i'm show you How to revive a dead 18650 or any Li-ion battery cell only 1 minute Waking up a dead sleeping 18650 Li-Ion battery Waking up a dead 18650 Li-Ion battery waking up 18650 how to recharge dead lithium ion battery الاستيقاظ من النوم الميت 18650 بطارية ليثيوم أيون الاستيقاظ ميتا 18650 بطارية ليثيوم أيون الاستيقاظ 18650 كيفية شحن بطارية ليثيوم أيون الميتة 死んだ寝る18650のリチウムイオン電池を目覚める 死んだ18650のリチウムイオン電池を目覚める 18650を目覚めさせる 死んだリチウムイオン電池を充電する方法 醒来睡觉18650锂离子电池 唤醒一个死亡的18650锂离子电池 醒来18650 如何给死了的锂离子电池充电 https://www.instagram.com/onlytechnicalshan https://www.facebook.com/onlytechnicalshan https://twitter.com/O_TechnicalShan
Views: 818 Only Technical Shan
Waking up a dead/sleeping 18650 Li-Ion battery
 
06:10
What you can do with them? (flashlight): https://www.youtube.com/watch?v=5L2FfZy_iQs Domino60 Waking up a dead/sleeping 18650 Li-Ion battery iMax B6 Music: Chances Silent Partner LiPo Dead Battery Waking Up LiPo / Li-Ion Dead Li-Ion battery Li-Ion battery LIION Battery Waking up dead/sleeping 18650 Li-Ion battery wakiing up 18680 battery
Views: 115900 Domino60
How to Make Lithium Drill Batteries Charge Again - Ryobi - Save Money
 
11:43
Use this trick to save $$$. I have had a bunch of these batteries just stop working and not take a charge one day. I finally decided to see if I could get this one working again instead of spending more money on batteries. Hopefully this trick will help save someone else some money. This is the AC Adapter I am using to attempt to put some charge back in the battery: http://amzn.to/2FPUYA6 See all My recommendations on my Amazon Page: https://www.amazon.com/shop/frugalpre... If you Found value in this Video Please Consider becoming a Patron of my Channel: https://www.patreon.com/frugalprepper
How To Fix A Dead Laptop Battery For Free - Hack
 
02:35
How To Fix A Dead Laptop Battery For Free - laptop battery Hack By finding dead cells in your laptop battery you can replace them with just about any other cell you find from an order system. Keep in mind that you will have to charge your dead bat. before removing it from the system so you more easily find the dead cells. Be sure to get your polarity right. usually the end of the cell with an indented band around it is the positive. Take apart your dead bat. this is going to be harder than you think. Scavenge some batteries from and older system and check for the best cells. remove dead cells from pack and replace with scavenged live cells from the older system. snap everything back together and plug into laptop. remember to plug into the wall on your first boot. After that you should be smooth sailing. Disclaimer - Do this at your own risk. I do not take any responsibility for your actions. R3DLIN3S redlines red lines
Views: 79272 R3DLIN3S
DIY: How to Revive a dead Ryobi 18V Li-Ion cordless power tool battery, plan B
 
31:17
In this video, I will show you how to revive a dead power tool battery. In my previous video, I showed you a similar method but this one is different. Previously the dead battery still had about 6V (from 18V). This time, this Ryobi battery has ZERO volt. Nothing. Nada. I tried the parallel method as shown in my first video but it did not work. So this time I have go to extreme length to get it working again. First video I did earlier to show you how to fix a Li-ion tool battery: https://www.youtube.com/watch?v=3e-RwVawEOs
Views: 107447 vuaeco
DIY Revive Lithium 18650 cells
 
02:49
here is how to revive an undervoltaged lithium cell. if you try to charge an undervolted cell with normal charge current, most of them will short out and break. if you don't have access to a universal power supply you can use a very high resistance resistor to limit the amps going into the battery.
Views: 50082 Rinoa Super-Genius
Li-Ion 18650 cells wake up / repair hack
 
04:04
My way of 18650 cells from old laptop batteries repair Be careful - it can be dangerous in case of cells in very bad condition
Views: 150113 cbm80amiga
Follow up video: Will it blow up? Reviving a dead 18650 Li-ion battery cell
 
05:07
This is a follow up video to my previous video on how to revive a dead 18650 cell: https://youtu.be/tbEfhPbqTDE
Views: 2508 vuaeco
Laptop Battery wont hold a charge FIX (doesn't last, charge or dies quickly)
 
07:49
So i was able to fix my laptop battery where the problem was it would last about 20 minutes then die. Also, the last time i attempted charging it it did not charge to the 100 percent mark. Well i show you a way to fix it in this video that actually works! Please be advised this procedure of fixing the battery is very dangerous. be safe. Also, you will need a lithium ion battery charger to charge the individual cells with. By the way, i did this to an ASUS ROG G752 Laptop.
Views: 2699 TRY to HELP you
Dewalt Battery Charging Fix
 
02:49
Dead Dewat battery that won't charge fix!
Views: 197116 richcan22
How to revive dead NiCd battery from cordless power tools
 
05:21
In this video I'll show you how to bring to life dead NiCd battery from cordless power tools. Nicd batteries often die in such a way that they won't take a charge and have zero voltage. This usually means they're shorted out by crystal dendrite growth inside Nicd cells. There's a method of bringing them back to life by zapping those shorted crystal dendrites away with too much current and voltage. Here is a link with DIY video: Ni-CD to lithium battery conversion by using 18650 Sony VTC5 cells: https://youtu.be/7W3-M50uE8w SKYRC iMAX B6AC V2 6A Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_282143.html?wid=21&lkid=10290452 SKYRC iMAX B6 mini Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_176503.html?wid=21&lkid=10290454 Support Well Done Tips on Patreon: https://www.patreon.com/welldonetips Due to factors beyond the control of WellDoneTips, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. WellDoneTips assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. WellDoneTips recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of WellDoneTips, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not WellDoneTips.
Views: 283995 Well Done Tips
How to revive a dead rechargeable power tool battery easily
 
03:24
How to revive a dead rechargeable power tool battery easily Rechargeable batteries for power tools sometimes will no longer charge but often these can be easily restored back to life with this simple method. The problem: You have a drill or other power tool with rechargeable batteries but one of the batteries is completely dead and when you plug it into the recharger unit it won't recharge at all. The manufacturers would tell you that you need to buy a new battery. When you look into it you find that the cost a new battery is so high that you may as well just buy a new drill that comes with a couple of new batteries. Well all is not lost! A friend in the UK told me about this method to revive a dead drill battery many years ago and I have used it successfully a number of times since. Basically, it seems that when a battery becomes completely discharged the charger unit effectively does not recognise that a battery has been inserted. This method puts enough charge into the battery so that it is not recognised by the charger and it gets recharged. I take the dead Dewalt battery and a good fully-charged battery and place them side by side. I then use a couple of pairs of scissors to connect the terminals together (plus to plus and negative to negative). I keep them connected for a minute or so and by then the dead battery has sufficient charge to be fully recharged by the charger unit. Of course you can use two pieces of wire or something else to connect the batteries together but I have found scissors work well when doing it by yourself with only one pair of hands. Although I have fix a Dewalt battery here I have used this method to fix other makes when the battery will not charge. So, in future, if you have a dead Nicd power tool battery try this power tool battery fix first before buying new. If you like my videos and feel like buying me a coffee you can can here - https://paypal.me/JPinFuerteventura Follow me on: Website: http://www.jpinfuerteventura.com Facebook: http://www.facebook.com/jpinfuerteven... Google+: http://plus.google.com/11712771568601... Instagram: http://instagram.com/jpinfuerteventura/ Twitter: http://twitter.com/JPinFuerte Holiday apartment to rent in El Cotillo: http://www.elcotilloapartment.com Information on El Cotillo: http://www.elcotillo.net
Views: 71357 JP in Fuerteventura
How To Get: Free 18650 Lithium Cells From Dead Laptop Batteries
 
05:49
In this video I'll show you how to get free lithium ion 18650 cells from old and dead laptop batteries. I'm ripping a part only dead or no more usable laptop batteries. Lots of them are a bust, but some of them still had good cells inside. Link to my home made 18650 cells charger: https://www.youtube.com/watch?v=KoHtxZG7leQ SKYRC iMAX B6AC V2 6A Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_282143.html?wid=21&lkid=10290452 SKYRC iMAX B6 mini Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_176503.html?wid=21&lkid=10290454 Support Well Done Tips on Patreon: https://www.patreon.com/welldonetips Due to factors beyond the control of WellDoneTips, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. WellDoneTips assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. WellDoneTips recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of WellDoneTips, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not WellDoneTips.
Views: 766595 Well Done Tips
Li-Ion battery short circuit,overcharge,undervoltage EXPERIMENT
 
05:01
Twitter: https://twitter.com/GreatScottLab Facebook: https://www.facebook.com/greatscottlab Previous video:http://youtu.be/FOZIPIqhvwI In this small experiment I will show you what can happen if you handle fake Ultrafire Li-Ion batteries the wrong way. I will demonstrate a short circuit, overcharge and undervoltage. Let's find out whether something will explode. Music: 2011 Lookalike by Bartlebeats You want to support my videos? You can browse and buy tools&materials from my Amazon Store. This way I get a small commission: Amazon.de: http://astore.amazon.de/great043-21 Amazon.com:http://astore.amazon.com/gre09a-20 Amazon.co.uk: http://astore.amazon.co.uk/gre0b-21 Or you feel super generous and want to use this Amazon link as your Amazon home page. And do not worry, your purchases are all anonym and the prices are all the same: Amazon.de:http://www.amazon.de/?_encoding=UTF8&camp=1638&creative=19454&linkCode=ur2&site-redirect=de&tag=great043-21&linkId=ORZEQZEOVJAFURCZ Amazon.com:http://www.amazon.com/?_encoding=UTF8&camp=1789&creative=390957&linkCode=ur2&tag=gre09a-20&linkId=I5NDCEAVCD2OWM4S Amazon.co.uk:http://www.amazon.co.uk/ref=as_li_ss_tl?_encoding=UTF8&camp=1634&creative=19450&linkCode=ur2&tag=gre0b-21
Views: 350988 GreatScott!
Revive/repair  20v lithium porter cable batteries
 
03:13
20volt 20v lithium ion battery wont charge porter cable
Views: 28199 John Realdoe
How to charge Porter Cable 20V Lithium Batterys that wont charge! Easy!
 
04:03
How to charge Porter Cable 20V Lithium that will not charge. Please do this at your own risk.
Views: 71819 Anthony Heath
RYOBI P102 "Dead" Lithium Battery Revival or "Jump Start"
 
09:22
Easy method to bring your RYOBI power tool lithium battery back to life. Please use all necessary safety precautions before attempting the procedure shown in this video. Batteries can explode if not handled with caution.
Views: 107295 Matt Eannarino
Ryobi Battery REVIVED! P105 18V LITHIUM
 
04:37
I have a model P105 ryobi 18 volt battery that i have successfully revived. I share with you what you need, what you gotta do and what you can possibly expect. Be safe!
Views: 5597 TRY to HELP you
How to revive a sleeping li-ion battery
 
01:45
U are at ur own risk I am not responsible
Views: 858 boosted garage
how to fix a dead rechargeable battery - revive restore rejuvenate jump start any damaged batteries
 
05:24
Battery Charger Amazon review: http://amzn.to/1TUbyNK Please subscribe to my channel: http://www.youtube.com/user/iesuck?sub_confirmation=1
Views: 63560 DIY Tinker
DIY How to revive/fix/rejuvenate/Repair/ recharge a bad dead rechargeable NiCd battery for cordless
 
02:32
Only works on NiCd batteries. Do not try on other battery types. In this video I take an old 18V NiCd battery that has not been used for 4 years, because it wouldn't hold a charge. My Ryobi battery that I used on all my cordless tools (circular saw, drill, reciprocating saw, vacuum, rotary saw, sander, and flashligh). You will need an alternate source that is around twice the voltage of the battery you want to rejuvenate. I need 36 volts and was only able to combine the 3 batteries I had to make 45V. I could have drained some charge down, but I decided to just use the 45V and it did the job. I connected my batteries in a series, but you can use any source that is about 36v. It is important that you follow these steps to get proper results. If you are not able to recharge after this you most likely have a dead cell. 1st - Fully drain your battery, so it shows no voltage on the meter. 2nd - Connect your batteries in a series. 3rd - Take the negative lead of your series and attach it to the negative terminal of your dead battery (I just taped it into place) 4th - take the positive lead from the series and quickly and repetitively tap it to the positive terminal of the dead battery for 5-7 seconds. 5th - Check current with the multimeter to make sure your dead battery accepted the charge. If it did not wait 5-10 minutes and try again, before determining you have another problem, just in case you made a mistake in the process the first time. 6th - wait 10-15 minutes before attempting to charge. 7th - Fully charge battery and test test on multimeter. 8th - Enjoy your newly rejuvenated battery This will work on most all NiCd batteries. This is a must for anyone with a cordless drill. Save your drill for years! Works for Dewalt, Sears, Craftsman, Ryobi, Porter-cable, Black & Decker, Kawasaki, Makita, Bosch, Milwaukee, Rigid, Panasonic, Ridgid, Hitachi, Snap-On, Cordless Max, Master Mechanic, Drill Master, and any other type of drill with a NiCd battery. Works on 9V, 9.6V, 12V, 14V, 14.4V 18V, 19.2V, 20V, or 9, 9.6, 12, 14, 14.4, 18, 19.2, 20 volt battery do it yourself and bring it back to life. DIY German DIY Wie / fix wieder zu beleben / verjüngen / Reparatur / tanken einen schlechten toten wiederaufladbare NiCd-Akku für schnurlose Russian Как оживить / исправление / омолодить / Ремонт / перезарядки плохой мертвой аккумуляторную NiCd аккумулятор для беспроводного Rabotayet tol'ko na nikel'-kadmiyevykh akkumulyatorov. Ne pytaytes' na drugikh tipov batarey. Spanish Cómo revivir / fix / rejuvenecer / Reparación / recargar una batería recargable muertos mal NiCd para inalámbrico Sólo funciona con baterías de NiCd. No trate de otros tipos de baterías. En este video me tomo una vieja batería de 18V NiCd que no ha sido utilizado desde hace 4 años, ya que no retiene la carga. Mi batería Ryobi que he usado en todos mis herramientas sin cable (sierra circular, taladro, sierra de sable, de vacío, sierra giratoria, lijadora, y flashligh). Usted necesitará una fuente alternativa que es alrededor de dos veces el voltaje de la batería que usted quiere rejuvenecer. Necesito 36 voltios y sólo era capaz de combinar las 3 baterías que tenía que hacer 45V. Yo podría haber drenado un poco de carga hacia abajo, pero decidí simplemente usar el 45V y no el trabajo. Me conecté mis pilas en una serie, pero se puede usar cualquier fuente que está a punto de 36v. Es importante que siga estos pasos para obtener resultados adecuados. Si usted no es capaz de recargar después de esto es muy probable que tenga una célula muerta. Primero - drenar completamente la batería, por lo que no muestra el voltaje en el medidor. 2 º - Conecte las baterías en una serie. 3 º - Tome el cable negativo de la serie y adjuntarlo a la terminal negativa de la batería muerta (Acabo grabó en su lugar) Cuarto - tome el cable positivo de la serie y de forma rápida y repetitivamente aprovechar al terminal positivo de la batería descargada durante 5-7 segundos. 5 º - Comprobar actual con el multímetro para asegurarse de que su batería muerta aceptó el cargo. Si no se hizo esperar 5-10 minutos e inténtelo de nuevo, antes de determinar que tiene otro problema, en caso de que cometió un error en el proceso de la primera vez. 6 º - esperar 10-15 minutos antes de intentar cargarla. 7 º - Cargue completamente la batería y test test de multímetro. 8 º - Disfrute de su batería recién rejuvenecido Esto funciona en la mayoría de todas las baterías de NiCd. Esto es una necesidad para cualquier persona con un taladro inalámbrico. Guarde su taladro por años! cualquier otra tipo de taladro con una batería de NiCd. Trabajos sobre 9V, 9.6V, 12V, 14V, 18V 14.4V, 19.2V, 20V, o 9, 9.6, 12, 14, 14.4, 18, 19.2, batería de 20 voltios hágalo usted mismo y traerlo de vuelta a la vida.
Views: 278809 You can Fix It!!!!
How To Double The Life Of Your Lithium Batteries
 
11:55
Learn how to make your own battery with my book DIY Lithium Batteries: http://amzn.to/2jbxvzS or check out my second book - The Ultimate DIY Ebike Guide: http://amzn.to/2BGx4Fn Checkout Steve's video showing his DIY battery tester/discharger: https://youtu.be/_3G9R6cLP0c Cycle Satiator charger: https://goo.gl/JRFKkz Luna charger: https://goo.gl/ozTmd4 EM3EV charger: https://goo.gl/TpsBrJ 350W hubmotor: https://goo.gl/K1mYvR 36V/48V controllers I used: https://goo.gl/nJBnJP Throttle: https://goo.gl/UebsNC Cycle Analyst: https://goo.gl/RsmE3N 350W Bafang BBS01: https://goo.gl/peyiYb 500W Bafang BBS02: https://goo.gl/EsqHu2 750W Bafang BBS02: https://goo.gl/k81aVH 1000W Bafang BBSHD: https://goo.gl/MU69oh The parts that I use for building batteries: 18650 cells (Sanyo GA 3500mAh): https://goo.gl/J6ONJV 18650 cells (another Sanyo GA 3500mAh source): https://goo.gl/f10wHH 18650 cells (Samsung 26F 2600mAh): https://goo.gl/VhpP7T 18650 cells (Panasonic 18650B 3400mAh): https://goo.gl/fvwJZQ 18650 cells (Another Panasonic 18650B): https://goo.gl/tVjREI 18650 positive insulating washer: https://goo.gl/HBVOuc Ebike battery cases: https://goo.gl/W2DLmE Nickel strip: http://goo.gl/VIrNQq Spot welder: https://goo.gl/KN3Uaw BMSs: http://goo.gl/S6gSQx Silicone wire: http://goo.gl/xmpbKD Black 18650 cell spacers: http://goo.gl/hQxWF6 Vruzend cell spacers: https://goo.gl/5ReLqA Large heat shrink tubing: http://goo.gl/6v1ow9 Small heat shrink tubing: https://goo.gl/OU3Z6u Foam sheet for protecting battery: http://goo.gl/5e71tE Kapton tape: https://goo.gl/D6BT57 Chargers: https://goo.gl/js0T0V ***Question response book giveaway rules*** When you guys asks questions in the comments of my videos, I'll try to answer them. If there are questions that I think would make a good video response, I'll choose them to do a longer segment. If I choose your question for a video response, you'll win a copy of my book The Ultimate DIY Ebike Guide (the paperback or the ebook), or my book DIY Lithium Batteries. Here are some things that YouTube makes me say: This contest is not sponsored by YouTube and YouTube isn't affiliated with it. I'm supposed to provide a link to the community guidelines for YouTube (http://www.youtube.com/t/community_guidelines). YouTube is not a sponsor of this "contest" and by participating, you are releasing YouTube from any potential liability, whatever that might be. Privacy notice: I won't steal your info. If you do win, you can choose to send me your address so I can mail you a paperback copy of the book (or some other prize if that changes) or you can send me an email address and I'll send you a copy of the ebook. I will do everything in my power to immediately forget your personal information afterwards. Music courtesy of Incompetech ("Groundwork")
Views: 75457 EbikeSchool.com
How dangerous are LiPo batteries? || Overcharge, Overdischarge, Short Circuit
 
05:20
Previous video: https://youtu.be/UtYbd89kVgY Facebook: https://www.facebook.com/greatscottlab Twitter: https://twitter.com/GreatScottLab Support me for more videos: https://www.patreon.com/GreatScott?ty=h In this video I will show you how important protection circuits are for LiPo batteries and what will happen if you accidentally overcharge or overdischarge your battery or even create a short circuit. Music: 2011 Lookalike by Bartlebeats Internet Sources: http://www.rchelicopterfun.com/rc-lipo-batteries.html http://www.epectec.com/batteries/cell-comparison.html You want to support my videos? You can browse and buy tools&materials from my Amazon Store. This way I get a small commission: Amazon.de: http://astore.amazon.de/great043-21 Amazon.com:http://astore.amazon.com/gre09a-20 Amazon.co.uk: http://astore.amazon.co.uk/gre0b-21 Or you feel super generous and want to use this Amazon link as your Amazon home page. And do not worry, your purchases are all anonym and the prices are all the same: Amazon.de:http://www.amazon.de/?_encoding=UTF8&camp=1638&creative=19454&linkCode=ur2&site-redirect=de&tag=great043-21&linkId=ORZEQZEOVJAFURCZ Amazon.com:http://www.amazon.com/?_encoding=UTF8&camp=1789&creative=390957&linkCode=ur2&tag=gre09a-20&linkId=I5NDCEAVCD2OWM4S
Views: 2099908 GreatScott!
Project: Upgrade Electric Bike to Lithium Batteries #1
 
09:49
Can I revive this old electric bike with a homemade lithium battery pack
Views: 155129 Julian Ilett
Repair Makita BL1830 Battery By Making One Good From Two Bad
 
07:28
In this video I'll take two bad Makita BL1830 lithium batteries and will make one good operating battery. Plus I’ll show you two ways, how to solve protection circuit problem, when it was triggered and regular Makita charger isn’t charging battery any more. 18V Li-ion Makita Battery Protect Circuit Board: https://goo.gl/OUWGpY iMax B6 AC V2 smart charger: http://www.gearbest.com/multi-rotor-parts/pp_282143.html?wid=21&lkid=10290452 Due to factors beyond the control of WellDoneTips, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. WellDoneTips assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. WellDoneTips recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of WellDoneTips, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not WellDoneTips.
Views: 224744 Well Done Tips
Makita 18Volt Lithium Ion Jump Starting Battery with a Boost
 
06:45
In this video I attempt to boost a dead Makita 18Volt Lithium Ion battery hooked up with two wires positive and negative to a good battery and place it on a charging unit. Makita BL1830 18-Volt LXT Lithium-Ion Battery https://goo.gl/1ZSZjC 2 Pack 18V 4.0Ah LXT Lithium-Ion Replacement Battery https://goo.gl/Zxqa87 Makita B-50289 47 Piece Ratcheting Screwdriver Accessory Assorted https://goo.gl/VPZubc
Views: 95259 Darren Charron
"Saving Private Li-ion" - Reviving a under-voltage (close to Zero Volt) Li-ion battery
 
08:02
A documentary video showing the process of reviving a under-voltage (close to Zero Volt) Li-ion battery using a Cadex Battery Analyser with Boast Function. The dead Li-ion cell is a newly purchased unit, but arrived dead upon arrival shipment with close to zero volt. A Universal Li-ion charger simply cannot detect and charge the dead battery, as the internal protection-circuit blocks any current from flowing into and out of the battery. After being processed by the Cadex boast function, the Universal charger immediately recognises the Li-ion cell and begins the charge process. Normal charging process can continue. NOTE: The calibration process on station #2 was shown for demonstration purpose only. Calibration on station #1 has already been performed prior to making this recording. Q: How do I get access to a Cadex C7200 if I do not own one? A: Kindly approach your nearest mobile phone retailer service centre. Most cellular shop will have one of these Cadex unit in their shop to help you to revive a Li-ion cell in sleep mode. Don't give up just yet! Q: Any more information on the battery revive/activation function? A: See: http://batteryuniversity.com/learn/article/low_voltage_cut_off
Views: 46082 Damo
Watch Diy: How To Revive A Dead 18650 (Or Any) Li-Ion Battery Cell - How To Revive A Dead Battery
 
01:00
EZ Battery Reconditioning! Click Here For More Information : https://bit.ly/2JHc1VT how to recharge a dead lead acid battery Lithium-ion Battery (Battery Cell Type) Battery revive a dead lead acid battery how to fix a 12v car battery epsome salt desulfate battery recondition your car battery How to Revive a Dead Battery Fix A Dead Laptop Battery how to revive dead battery How-to (Website Category) Magnesium Sulfate (Drug) Reconditioning a Battery Dead Laptop Battery Battery reconditioning battery reconditioning maintain that battery Battery survival trick revive a dead mobile Recharge car battery fix inverter battery mobile not charging lithium ion battery Car won't start revive dead battery recondition battery Battery (Invention) epsom salt battery revive lithium ion battery desulfating battery mercedessource.com deep cycle battery desulfate battery boondocking solar sealed lead acid revive a battery Recharge battery revive batteries repair batteries hack of the day Dead car battery old card battery do it yourself lithium battery battery charger off grid solar mobile battery Battery repair John Milandred marine battery mercedessource No car lights How To Fix
Views: 1 kamui zuka
How to charge A DEAD Ryobi 18 volt rechargeable battery! IT WORKS!!
 
01:49
If this helped you how about throwing me a buck on paypal? chaseme81871@aol.com is the paypal. How to fix Ryobi 18volt batteries that wont charge . we all know they are a POS! THIS WILL REALLY HELP YOU.
Views: 340920 chaseme81871
Laptop Battery not charging "plugged in, not charging" Free Easy Battery Fix
 
03:25
In this video you'll see a Laptop Battery "plugged in, not charging" free easy fix. Plugin not charging is simple to fix with this free easy battery calibration. A laptop battery not charging fix solution can be done in only a few minutes. Laptop battery not charging while plugged in to AC power is a common problem among laptop owners. However, I show you how to solve it quick and easy. Is this a laptop battery rebuilding project without any special tools? Absolutely!!! This battery calibration will extend your laptop battery life so you can get few more months of battery life extended. So do the easy fix and do a simple laptop battery calibration today. My video tutorial will help you resolve your laptop battery plugin not charging error or laptop battery not charging fully error message. Get an easy battery fix by watching my video and don't sweat the how to fix laptop battery not charging problem ever again. http://youtu.be/XcDvp2A7Fss
Views: 2871486 nickscomputerfix
Revive/Recover/Charge Dead Lithium Batteries, EZ and Safe, Full Version
 
20:24
Revive/Recover/Charge Dead Lithium Batteries, EZ and Safe, Full Version Battery Capacity Meter and My Charger Mod
Views: 291 Tek Geek
How To Charge Lithium (18650) Battery | Recycle Old Laptop Battery | Get 18650 Battery For Free
 
02:09
Hi Everyone Toady i'm Going To Show you How to Recycle Your Old Laptop Battery And How to Charge Them Safely . If you Have any Question Please Comment . How to Open Battery Pack - https://youtu.be/Lut8JOUFP2s Where To Buy "Cheapest" Panasonic 3400mAh 18650 100% Original - https://goo.gl/IuJdh9 Battery Charging Board - https://goo.gl/Wi9Gsh 18650 BMS - https://goo.gl/gV6K0u Vichy VC99 Multimeter - https://goo.gl/VuNQw7 Full Details - https://goo.gl/hSI6i6 #Tags Recycle Old Laptop Battery Get 18650 Battery For Free How To Charge Lithium (18650) Battery How To Charge Lithium Battery Recycle Old Dead Laptop Battery How to Charge Lithium Battery Safely Lithium Battery BMS How To make a Lithium Battery BMS How to make a Power Bank How to Charge Lithium Battery At Home Lithium Battery Easy Solution 18650 Battery 100% Original Brand 6PCS 18650 3400mAh 3.7v Rechargeable Battery Li-ion Batteries For Panasonic NCR18650B Where To Buy 100% Original Panasonic 3400mAh 18650 18650 Lithium Battery Charging Board Charger Module+Protection Dual Functions TP4056
Views: 36360 Steve Willson Kujur
Fix a Dead Drill Battery That Wont Charge- Don't Throw it Away!
 
02:52
How I fixed my completely dead drill battery. Works fine again See more of my Electronics and Repair videos here: https://www.youtube.com/playlist?list=PLxyM2a_cfnzh9sbbEMFvFAGvNKfSElkvC Remember to subscribe for more videos! https://goo.gl/2qaJ2U My Black & Decker drill decided to complete stop working and would not charge or function with the factory battery charger. I knew the battery had only a few cycles on it so it should be recoverable. The stock charger refuses to apply any charge if the cells are not at the correct level. Here's an easy fix anyone can do just be careful. I used this drill all day afterward at the capacity seems right back to 100%. Beats the heck out of throwing it away. ------------------------------------------------------ Get Social with Me! Google Plus ➢ https://goo.gl/4o2wMu Twitter ➢ http://twitter.com/MKmeOrg Instagram ➢ https://instagram.com/mkmeorg/ SnapChat ➢mkmeorg Facebook ➢http://www.facebook.com/EricWilliam13 ----------------------------------------------------- Shop at Amazon and support my channel: Shop Amazon US ➢http://www.amazon.com/?rw_useCurrentProtocol=1&tag=mkmeorgstore-20 Shop Amazon CAN ➢http://www.amazon.ca/?rw_useCurrentProtocol=1&tag=mkmeorg0d-20 Shop the MKme.org Store ➢http://store.mkme.org ----------------------------------------------------- My Website and Related: Main Site ➢ http://mkme.org Blog ➢ http://blog.mkme.org Patreon ➢ http://www.patreon.com/EricWilliam G+ Community ➢ http://goo.gl/6rMPsi MKme Facebook Page ➢ http://goo.gl/aXg29 ----------------------------------------------------- Thanks for Subscribing!
Views: 172887 MKme Lab
DIY: Ni-Cd To Lithium Battery Conversion By Using 18650 Cells
 
12:19
In this video I'll transform this old, cordless power drill Ni-Cd battery to lithium battery by using 18650 Sony VTC5 cells. Update! From the date when video was made pased some time and Sony released new version of high drain cells with bigger capacity 3120mAh - VTC6. Genuine Sony VTC6 cells could be bought here: 2 pcs - https://goo.gl/2TyRsB 4 pcs - https://goo.gl/GeqJTX 8 pcs - https://goo.gl/WfYuXB Authentic Sony US18650VTC5 2600mAh cells came from Gearbest.com: 4pcs: http://www.gearbest.com/batteries/pp_357766.html?wid=21&lkid=10290430 8pcs: http://www.gearbest.com/batteries/pp_399867.html?wid=21&lkid=10290436 SKYRC iMAX B6AC V2 6A Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_282143.html?wid=21&lkid=10290452 SKYRC iMAX B6 mini Balance Charger: http://www.gearbest.com/multi-rotor-parts/pp_176503.html?wid=21&lkid=10290454 Support Well Done Tips on Patreon: https://www.patreon.com/welldonetips Due to factors beyond the control of WellDoneTips, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. WellDoneTips assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. WellDoneTips recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of WellDoneTips, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not WellDoneTips.
Views: 1823115 Well Done Tips
Repair laptop battery at home|| how to open laptop battery and rebuild after repairing
 
08:54
#reconditionbattery #laptopbattery #liioncells Laptop battery reconditioning, Battery repairing of Laptop. This video shows how to re-use your exhausted laptop battery with the help of old battery of laptop. I have shown replacement of dead cells (Li-ion batteries) of the exhausted battery with the proper Li-ion cells (3.7 V rechargeable batteries). I have successfully replaced the old batteries and now it is working fine and giving me the backup of 2 hrs approximately.. Thanks for watching my video. from --------- N.K. Innovative Ideas. Purchase online Li-ion Cells 2600mAH Amazon Affiliate: http://amzn.to/2EPpSbT for more innovative videos please click the link below and subscribe innovative ideas: https://www.youtube.com/innovativeideas My facebook Page link is : https://www.facebook.com/powercomputersmainpuri/ and Google Plus Page is : https://plus.google.com/u/0/+NAKULSHAKYA My Playlists are : 1. Tech Videos in English https://www.youtube.com/playlist?list=PLL4O1t6dXh9RJuyVU7sIoyBRddiPn7thO 2. Do It Yourself Electronics https://www.youtube.com/playlist?list=PLL4O1t6dXh9T5Zd91bLMBHQXye0SFw04F 3.DO IT YOURSELF COMPUTERS AND PRINTERS https://www.youtube.com/playlist?list=PLL4O1t6dXh9Tp6z2ExUKul-jGrplO8Hky https://www.youtube.com/innovativeideas
Views: 198591 INNOVATIVE IDEAS