Videos uploaded by user β€œhameed wafa”
Kenmore dishwasher won't start
Reseted works OK 😊
Views: 34467 hameed wafa
how to test frigidaire washer door lock assembly
Measure the wax motor (the brown piece on the right ) resistance. The normal reading should be close to 1500 Ohms, part #131763202
Views: 28316 hameed wafa
whirlpool gold dishwasher wont start
dishwasher wont start clean light is flashing,fixed
Views: 19819 hameed wafa
GE Microwave Turntable Won't Turn
Views: 33259 hameed wafa
Kenmore stove F11 error code fixed
Kenmore or Frigidaire F11 has the same meaning, communication problem between main board and display touch pad, or stuck key error, just by peeling it off and cleaning it, you would fix the problem πŸ˜€
Views: 12682 hameed wafa
Kenmore dishwasher clean light flashing
Here how you reset relay on control board on this model clean light was flashing about 7 times
Views: 18443 hameed wafa
Samsung washer diagnostic mode
Error code AE6 = communication problem between inverter board and user interface board, check all the wires and connections, if didn't find any problem, replace main board located at the back πŸ˜€
Views: 70312 hameed wafa
Panasonic microwave runs for 2 seconds then shuts off
Checked everything, found out that my main control board was defective πŸ˜…
Views: 3860 hameed wafa
Diagnostic mode for Frigidaire affinity washer
At this moment in this washer the main problem is maintained control board not the motor, e56 error is high current to motor, but in this unit it is the main board. Also by holding start/pause and cancel at the same time with two fingers, will also show you the error code on this unit πŸ˜€
Views: 31148 hameed wafa
Fridge keeps tripping the circuit breaker
Had defective compressor,
Views: 15529 hameed wafa
F0E1 error code front load washer
Found defective wash motor,
Views: 5818 hameed wafa
frigidaire gas stove F10 error code
A faulty RTD sensor probe is one of the causes for an F10 code or overheating oven. The sensor probe is supposed to detect the exact temperature in the Frigidaire electric range cavity and relay it to the oven's main control so it knows when to shut off the heating elements,
Views: 3195 hameed wafa
How to find leak on a fridge
Gave her 200 psi nitrogen used soapy water to find the leak, so I didn't had to replace evaporator and heat exchanger like always. Found the leak replaced the dryer filter and fixed it
Views: 19083 hameed wafa
Kenmore microwave won't start
Microwave won't start because the door was not latching properly or not engaged to the top micro switch fixed it πŸ˜€
Views: 8765 hameed wafa
Maytag dishwasher leaks
This unit is more then 15 years old, and yes there was 3 Philips screws used on each side trim.
Views: 731 hameed wafa
Microwave not heating
Microwave is not heating, replaced only diode and it works now.
Views: 25754 hameed wafa
Frigidaire affinity dryer is dead, πŸ˜‚ I don't know why I said washer πŸ˜†
Model number AEQ6000ES Part replaced thermal limiter 134120900 please clean your vent hose, before using the dryer 😘
Views: 516 hameed wafa
F51 error code whirlpool cabrio
F then 51 flashes when there is a motor rotor position sensor (RPS) failure or lower harness problem. I recommend you to use loctite on the screw when retighting it back. I did not had loctite, it should be fine.
Views: 1868 hameed wafa
Whirlpool dishwasher leaks from bottom
Replaced grommet fixed it πŸ˜‰
Views: 11147 hameed wafa
Kitchenaid fridge leaks from water filter base
Couple problems fixed
Views: 3650 hameed wafa
washer keeps filling with water
Even washer is off, it still fills with water, bad water valve fixed
Views: 30457 hameed wafa
GE dishwasher makes noise and not cleaning properly
Cleaned spray arms and found a piece of glass from drain pump or filter place
Views: 6285 hameed wafa
Whirlpool washer calibration mode
After replacement of, main control board, wash motor, shift actuator, door lock, pressure sensor, you need to run calibration mode, otherwise the washer would not work properly πŸ˜‰
Views: 9503 hameed wafa
Kenmore elite dishwasher diagnosis
Dishwasher was not washing properly, wash motor was very weak,
Views: 10971 hameed wafa
Samsung microwave blows the fuse
Found defective micro switch fixed it.
Views: 2362 hameed wafa
F3E2 error code maytag washer
Found 2 cracked wires at the temperature sensor at the back of the unit once wire was almost broken, that's why everytime it was agitating it was creating error code, resoldered it back, works perfectly fine πŸ˜€
Views: 2109 hameed wafa
Samsung washer noisey and burning smell
Inspect unit, had defective bearing πŸ˜… the smoke is normal only when the bearing is defective πŸ˜‚ not all the time.
Views: 10036 hameed wafa
GE microwave is dead
The problem was with noise filter. Repaired it, works fine now.
Views: 787 hameed wafa
Whirlpool dishwashers control board fixed for free
Whirlpool dishwasher control board fixed for free
Views: 34878 hameed wafa
Maytag bravos washer diagnostic mode
How to put Maytag bravos washer on diagnostic mood, it has no LCD display
Views: 16343 hameed wafa
Copy of how to replace t.3 thermistor in Electrolux fridge on its ice maker
how to replace thermistor in Electrolux fridge on its ice maker.or how to replace t3 sensor on ice maker
Views: 3329 hameed wafa
Estate dryer heater stays on
Defective heat element shorted to ground part01
Views: 1275 hameed wafa
Whirlpool dishwasher leaks from bottom part 1
Replaced grommet fixed it.
Views: 8851 hameed wafa
How to replace heater in Samsung dishwasher, from underneath  πŸ˜‰
I have seen everyone takes the front control board and front kick plate out to replace heating element on Samsung dishwashers, but this way it's easy.and yes customer was getting HE error code.which is heater error.
Views: 202 hameed wafa
E15 error code kenmore dishwasher
Leaked water
Views: 5385 hameed wafa
Estat dryer heater stays on
Estat dryer heater stays on part02
Views: 573 hameed wafa
lexus is300 Cigarette lighter not working
my cigarette lighter was not working found the blown fuse and fixed it.
Views: 21517 hameed wafa
E3 error code samsung washer
E3 = Hall sensor and motor problem,control board, loose wire, bearing.In this case, bearing was broken. And hall sensor was not reading the motor speed, creating e3 error code.
Views: 49801 hameed wafa
Ultra wash quietguard standard, self diagnosis mood
This dishwasher was not functioning properly, there was stuck relay on the board, after self diagnosis it will reset everything and works OK z
Views: 3166 hameed wafa
Dacor microwave intermittent heat
Found defective microwave switch replaced it, works fine now.
Views: 279 hameed wafa
kenmore dryer makes thumping noise
samsung dryer makes thump noise
Views: 785 hameed wafa
Kenmore washer drum seized
Bearing is broken, not worth to fix.made by Samsung πŸ˜‰
Views: 352 hameed wafa
Bosch gas range convection fan does not work
Replaced display, fixed the problem,
Views: 301 hameed wafa
Samsung washer noisey and burning smell part 2
Ordered bearing to fix it unfortunately the problem was big 😬
Views: 4086 hameed wafa
Dacor venthood reset
This home owner was not able to turn off/on lights unless play around with fan switch ;)
Views: 742 hameed wafa